Weatherboard and Shiplap Cladding Spraying in Southampton and Hampshire
Faded weatherboard, shiplap and feather-edge cladding can be sprayed any colour on-site across Southampton and Hampshire — which boards can be sprayed, the process, colours and the cost against re-cladding.
Weatherboard and Shiplap Cladding Spraying in Southampton and Hampshire
Weatherboard and shiplap cladding gives a building its character — until the colour goes. UPVC and composite boards chalk and fade, dark and woodgrain finishes wash out on south-facing elevations, and a frontage that is structurally fine starts to look tired and dated. Spraying recolours the boards in place, in any colour, for a fraction of the cost of stripping and re-cladding.
It is part of the cladding spraying service we run on-site across Hampshire, and specifically for homes and commercial units around Southampton.
What Kind of Boarding Can Be Sprayed?
Almost all of it, with the correct preparation and primer for the material:
- UPVC and PVC shiplap, weatherboard and feather-edge cladding.
- Composite and cellular boards, including the popular wood-effect ranges.
- Fibre-cement weatherboarding, with an adhesion primer suited to the board.
- Cladding on gables, dormers, porches, full elevations and commercial soffits.
If you are not sure what your boards are made of, our guide to composite versus metal cladding spraying explains how the material changes the preparation — and a survey confirms it before anything is quoted.
Why Spray Rather Than Replace?
Re-cladding an elevation means boards, battens, breather membrane, trims and days of labour, and it puts a skip of perfectly sound material into landfill. Where the boards are physically intact and only the finish has failed, spraying restores them at a fraction of the cost, usually in one to two days, with no scaffolding-bound weeks and no disruption inside the building.
When boards are genuinely damaged rather than just faded, spraying is not the answer — our guide to cladding respray versus replacement sets out where the line sits, and the survey tells you honestly which side your cladding is on.
The Weatherboard Spraying Process
Every board is washed and degreased, then masked and primed with an adhesion primer matched to the material. Specialist exterior topcoats are spray-applied for an even, factory-grade film that follows the shiplap profile without runs or brush marks. The shadow lines and texture that give weatherboarding its look are preserved — the boards simply get their colour back.
Colours and Finishes
Any RAL or BS colour is available. Weatherboarding is most often sprayed in the modern exterior palette — anthracite grey, sage and heritage greens, off-whites and soft blacks — and can be matched to newly sprayed windows, doors and fascias so the whole elevation reads as one scheme. Matt and satin finishes are both available; matt tends to suit contemporary boarding, satin the more traditional look.
Book a Free Survey
If your weatherboard or shiplap cladding is fading, chalking or simply the wrong colour, a free survey will confirm what your boards are, what preparation they need and a fixed written quote. Start from our cladding spraying service page, or our Southampton cladding page for local work.
Frequently Asked Questions
Can UPVC weatherboard cladding be sprayed?
Yes. With degreasing and an adhesion primer made for exterior plastics, UPVC and PVC weatherboard and shiplap take a sprayed finish extremely well. The shiplap profile and shadow lines are preserved — only the colour changes.
How much does it cost to spray weatherboard cladding?
It is priced by area and condition, and is consistently a fraction of the cost of re-cladding the same elevation. A single gable costs far less than full elevations; a free survey confirms a fixed written quote.
What colours can weatherboard cladding be sprayed?
Any RAL or BS shade, in matt or satin. Anthracite grey, heritage greens and off-whites are the most popular, and cladding is often matched to sprayed windows, doors and fascias for one consistent scheme.
How long does sprayed weatherboard last?
The topcoats are UV-stable and formulated for exterior use, so they hold colour against sun and weather. The finish is backed by a written guarantee confirmed with the quote.
Need On-Site Cladding Respray?
On-site spray coating for composite panels, metal cladding, and weatherboard. Restore faded finishes across Hampshire without the cost of replacement.
